CH376S USB HOST BOARD
₹289.00 Incl. GSTCH376S is used as a file manage control chip, used to MCU system read/write a file in USB Flash Drive or SD card. It supports USB-Device Mode and USB-HOST Mode. It also sets firmware of special communication protocol to deal with Mass-Storage devices, communication interface firmware of SD card, FAT16, FAT32, and FAT12 file system manage firmware in the inner. CH376S supports three communication interfaces: an 8-bit parallel, SPI interface or asynchronism serial interface.
CNC shield V3 for Engraving Machine A4988 DRV8825 driver expansion board
₹98.00 Incl. GSTThis expansion board as a driver expansion board, can be used for engraving machines, 3D printers, CNC. It is a total of four slots, can drive four A4988 stepper motor. Each road stepper motors only need two IO ports. In other words, six IO ports can be well managed three stepper motors.
The CNC shield V3 for Engraving Machine 3D Printer A4988 DRV8825 driver expansion board is very convenient to use.
After insert Arduino CNC Shield V3.0 into Arduino UNO, and installed GRBL firmware then you can quickly DIY a CNC engraving machine.
Coin Acceptor MULTICOIN
₹895.00 Incl. GSTHow to Configure the Vending Machine Coin Acceptor (Multi-Coin Acceptor):
- Press the setting key (8) to choose several currency systems.
- Use the accurate key or broaden key to increase or decrease the numerical value.
- Press the setting key once the setup is complete to confirm.
- The letter H will appear in the sentence (the quantity of sampling for various currency values).
- The letter P will appear in the sentence (the numerical value for signal output of various currency values).
- The letter F will appear in the sentence (the precision of various currency values).
- Set the desired money according to the parity of argumentation.
- Turn off the power when the letter E appears so that it can reopen.
The multi-coin reader machine can take up to six different kinds of coins and tokens from across the world. It has an integrated intelligent CPU software control for high accuracy. Self-programming features are also included. It guards against electromagnetic interference and electrical shocks.
COLOR SENSOR TCS3200
₹434.00 Incl. GSTGY-31 Color Sensor Module is made using IC TCS3200, a programmable color light to a frequency converter. It has configurable silicon photodiodes and a current to frequency converter in a single monolithic CMOS Integrated Circuit. Its output is a square wave having a 50% duty cycle with frequency directly proportional to irradiance (light intensity). This module can be directly interfaced with Microcontrollers, Arduino Boards, Raspberry Pi, etc.
CR2354 BATTERY
₹203.00 Incl. GSTCR Series Lithium coin button batteries from Panasonic. These batteries are available in a variety of different sizes and capacity options to suit your application. These non-rechargeable batteries are ideal for smaller electronic devices and have a longer lasting life than alkaline equivalents. These batteries are small, round and slim and are normally used on their own but with their less self-discharge they are able to hold their charge for a longer period of time.
CURRENT SENSOR(ACS712-5A)
₹5.00 Incl. GSTThe 5A range Current Sensor Module ACS712 consists of a precise, low-offset, linear Hall circuit with a copper conduction path located near the surface of the die. Applied current flowing through this copper conduction path generates a magnetic field in which the Hall IC converts into a proportional voltage.
Sensing and controlling current flow is a fundamental requirement in a wide variety of applications including, over-current protection circuits, battery chargers, switching mode power supplies, digital watt meters, programmable current sources, etc.
This ACS721 current module is based on the ACS712 sensor, which can accurately detect AC or DC current.
The maximum AC or DC that can be detected can reach 5A, and the present current signal can be read via analog I / O port of Arduino.
D4184 Mosfet Module
₹49.00 Incl. GSTWith optocoupler isolation, the control signal and the power of the controlled device are isolated, which greatly increases the rigidity of the interference. PWM speed regulation widely used to control the start and stop of the motor. The signal input side can be welded to the terminal or pin itself, compatible breadboard output can be soldered to the terminal or direct wire.
DF MINI
₹24.00 Incl. GSTMP3-TF-16P MP3 Disk TF Card Module Serial Port is a compact and inexpensive MP3 module that can be connected directly to the speaker. Module with battery power supply, speaker, the keypad can be used alone, or through the serial port control, as the Arduino UNO or any microcontroller with a serial port module. The module itself perfectly integrated hardware decode MP3, WAV, WMA.
While the software supports TF card driver to support FAT16, FAT32 file system. It can be done by simple serial command plays the specified music, as well as how to play music and other functions, without tedious low-level, easy to use, stable and reliable.
DhT-11 Module
₹49.00 Incl. GSTThe DHT-11 Digital Temperature And Humidity Sensor is a basic, ultra low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).
DHT-22 MODULE
₹108.00 Incl. GSTIf you are wandering to build a device that detects temperature and humidity from the atmosphere, then This sensor is needed for you.
The DHT22 Digital Temperature and Humidity Sensor Module AM2302 is a basic, low-cost digital temperature and humidity sensor. It uses a capacitive humidity sensor and a thermistor to measure the surrounding air and spits out a digital signal on the data pin (no analog input pins needed).
DISSOLVE OXYGEN SENSOR WITH PH BOARD
₹142.00 Incl. GSTPreparing the Dissolved Oxygen Level Sensor Probe:
For a new dissolved oxygen probe, first thing to remember begin by adding 7.5% KCL solution into the membrane cap as the filling solution. Follow these steps:
- Remove the membrane crown.
- Place the DO membrane on the cap and fix the crown to the electrolyte tube, covering one side of the membrane.
- Ensure the membrane has no wrinkles and is not punctured or damaged.
- Unscrew the membrane cap from the probe and fill about 2/3 volume of the cap with KCL solution.
- Keep the probe in a vertical position concerning the horizontal plane.
- Carefully screw the cap back onto the probe. Some solution overflow is acceptable to ensure the probe is fully filled with KCL solution, eliminating air bubbles.
- The 7.5% KCL solution acts as a suitable electrolyte in the DO Probe.
- The electrode tube should be free of air bubbles to prevent fluctuations in readings.
DS18B20 Temperature Sensor Module
₹45.00 Incl. GSTDS18B20 Temperature Sensor is suitable for the cold storage, granaries, storage tanks, telecommunications room, electric power room, cable trough, and other temperature measurement and control areas; bearing, cylinder, textile machinery, air conditioning, and other small space industrial equipment temperature and control; , Refrigerator, freezer, and low-temperature drying oven, etc. heating/cooling pipe calorie measurement, central air conditioning household thermal energy measurement and industrial temperature measurement and control and Many more..