Get the high-quality Force pressure sensor 0.5-inch diameter at a low price. This is a force-sensitive resistor with a round, 0.5″ diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area.

The harder the force, the lower the resistance. When no pressure is been apply to the FSR its resistance will be larger than 1MΩ. This FSR can sense applied force anywhere in the range of 100g-10kg.

Two pins extend from the bottom of the sensor with 0.1″ pitch making it bread friendly. There is a peel-and-stick rubber backing on the other side of the sensing area to mount the FSR. Just Connect a resistor to form a voltage divider and measure the voltage at the junction to find the force applied.

Get the high-quality Force pressure sensor 0.5-inch diameter at a low price. This is a force-sensitive resistor with a round, 0.5″ diameter, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the sensing area.

The harder the force, the lower the resistance. When no pressure is been apply to the FSR its resistance will be larger than 1MΩ. This FSR can sense applied force anywhere in the range of 100g-10kg.

Two pins extend from the bottom of the sensor with 0.1″ pitch making it bread friendly. There is a peel-and-stick rubber backing on the other side of the sensing area to mount the FSR. Just Connect a resistor to form a voltage divider and measure the voltage at the junction to find the force applied.

FR120N Mosfet control Module Replacement Relay comes with optocoupler isolation, the control signal and the power of the controlled device are isolated, which greatly increases the rigidity of the interference. PWM speed regulation widely used to control the start and stop of the motor. The signal input side can be welded to the terminal or pin itself, compatible breadboard output can be soldered to the terminal or direct wire.

MPU9250 9-Axis Attitude Gyro Accelerometer Magnetometer Sensor Module features the MPU-9250, which is a multi-chip module (MCM) consisting of two dies integrated into a single QFN package. One die houses the 3-Axis  accelerometer and gyroscope. The other die houses the AK8963 3-Axis magnetometer. Hence, the MPU-9250 is a 9-axis Motion Tracking device that combines a 3-axis accelerometer, gyroscope and magnetometer, and a Digital Motion Processor (DMP). It is based on I2C Address, Address: 0x68 by default, 0x69 if AD0 is pulled high.

1. Integration Lowers System Cost, Simplifies Design
2. Efforts, and Reduces Design Cycle Time
3. High Accuracy Facilitates Meeting Error Budgets
4. 15-Bit ADC Resolution; Nominal Temperature
5. Resolution 0.03125NC (Varies Due to RTD Nonlinearity)
6. Total Accuracy Over All Operating Conditions:
7. 0.5NC (0.05% of Full Scale) max
8. Fully Differential VREF Inputs
9. 21ms (max) Conversion Time
10. Integrated Fault Detection Increases System Reliability
11. 45V Input Protection
12. Fault Detection (Open RTD Element, RTD Shorted to Out-of-Range Voltage, or Short Across RTD Element)

The Si5351A clock generator is an I2C controller clock generator. It uses the onboard precision clock to drive multiple PLL’s and clock dividers using I2C instructions. By setting up the PLL and dividers you can create precise and arbitrary frequencies. There are three independent outputs, and each one can have a different frequency. Outputs are 3Vpp, either through a breadboard-friendly header or, for RF work, an optional SMA connector.

Provide Arduino, 51, stm32 microcontroller communication program. GY-56 can set the upper and lower limit distance alarm value, switch output, In the set interval, there is a block of the measured object and a high level is directly output. Under the IIC mode, you can set different internal IIC addresses if necessary.