ADS1256 24BIT ADC MODULE
Testing Methods
ARDUINO NANO CH340 WITH SOLDERED PINS
₹228.00 Incl. GSTThe CH340 Soldered Nano Board R3 Chip without USB Cable chipboard is based on the famous Arduino platform and does all the functions of Uno, but with a smaller footprint.
Nano CH340 Soldered Board R3 Chip without USB cable is vital for your small project where you don’t need much of a pin-outs but the small size is very important to make it look good.
The Nano equips a low-cost USB-Serial Chip that makes it less in price than Nano with FTDI USB-Serial Chip used on older versions of Arduino Nano.
The Nano is a small, complete, and breadboard-friendly board based on the ATmega328 (Arduino Nano R3). It has more or less the same functionality of the Arduino Uno but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one.
The Nano can be power via the mini-USB connection, 6-20V unregulated external power supply (pin 30), or 5V regulated external power supply (pin 27). The power source is automatically selected to the highest voltage source.
The size of Nano V3.0 with CH340 Chip is only 43 mm x 18 mm; it comes with 6 PWM I/O from the total of 14 digitals I/O, 8 analog inputs, 16Mhz clock speed and 32kB of flash memory.
ARDUINO UNO SMD
₹237.00 Incl. GST- Easy application programming using open source IDE
- Easy to learn Microcontroller using Arduino boards.
- Easy application programming using open source IDE
- Ready Library for most of the sensors and application modules.
- More information on www.arduino.cc
ATTINY 85 BOARD MICRO USB
Features :
- High Performance, Low Power AVR® 8-Bit Microcontroller
- Non-volatile Program and Data Memories
- 8K Bytes of In-System Programmable Program Memory Flash
- Endurance: 10,000 Write/Erase Cycles
- 512 Bytes In-System Programmable EEPROM
- 512 Bytes Internal SRAM
- Peripheral Features
- Two High-Frequency PWM Outputs with Separate Output Compare Registers
- USI – Universal Serial Interface (12C, SPI, 1-wire) with Start Condition Detector
- 10-bit ADC
- 4 Single Ended Channels
- Two Differential ADC Channel Pairs with Programmable Gain (1x, 20x)
- Speed Grade
- 0 – 10 MHz @ 2.7 – 5.5V, 0 – 20 MHz @ 4.5 – 5.5V
- Industrial Temperature Range
- Low Power Consumption
- Active Mode:1 MHz, 1.8V: 300 µA
Bbc Micro Bit Go V2
Features:
- 5×5 LED Matrix Display (Red LEDs)
- Two Programmable Buttons
- Touch Sensitive micro:bit logo
- Additional Power Indicator LED and Mic input indicator LED
- Built-in MEMS microphone input
- Onboard Accelerometer, Compass, Light and Temperature Sensors
- Wireless Communication, via Bluetooth 5.1 and BLE and 2.4GHz Radio
- Edge Connectors:
- Total 25 pins: 20 smaller pitch to pitch pins, 5 RINGS Notched Edge pins
- 4 Dedicated GPIO, PWM, I2C, SPI, Power and etc.
- 5 Ring pins for connecting crocodile clips or banana plugs
- 20-pin Edge Connectors, 5 notched edge Connectors
- Dedicated I2C bus for peripherals
- Power Button to power off the MCU
- Micro USB Type-B Connector
- JST-PH Battery Connector (Not JST-XH)
- Reset Button with Status LED
- Available current for external devices: 200mA
- Programming Platform: C++, Make code, Python, Scratch
LPC1768 ARM Cortex M3 Development Board
Blue Board- LPC1768 is an evaluation board for LPC1768 CORTEX M3 based microcontroller. The LPC1768 microcontroller has 512KB of internal flash and 64KB SRAM. Following are the salient features of the board.
LPC2148 Medium Boards ARM7
Programming LPC2148 ARM7 Development board:
LPC2148 Board can be programmed through serial port UART “0” using “LPC2000 flash utility V2.2.2” it is an freeware windows utility used to download the hex file format onto the LPC2148 Board. If your PC does not have a serial port then use a USB to serial converter to download the hex file on the board.
- Open LPC2000 Flash Utility V2.2.2
- Browse File name and Select the hex file to be downloaded.
- Select Device as LPC2148
- Set XTL Freq [KHz] to 12000
- Blank Check: Entire Device
- Select the appropriate com port (See your “device manager” to find out the com port number)
- Select the Baud Rate in between 9600 and 38400
- Uncheck “Use DTR/RTS for Reset and Boot Loader Selection”
- Click on Read Device ID.
To make the board enter programming mode:
- Hold down ISP and RESET Buttons, then release RESET first and finally ISP.
- The controller enters the bootloader mode.
- It will display as “Read device ID Successful”.
- Click on the Upload to Flash Button.
- Program uploaded successfully.
- Click the Rest Button on the Board. That’s it, your hex file is on the board.
- Enjoy your code output.
STM 32F 103 DEV BOARD Imp ORG Chip
Features:
- Minimum System Design
- Versatile Connectivity
- Compact Form Factor
XH-W3230 temperature controller 220V AC
Features:
- Mini temperature controller.
- With a clear LED display for better readability.
- Wide temperature measuring range.
- Heating or cooling control.
- All parameters set can be saved after a short circuit.
- Relay output.
- High Control precision 0.1 centigrade